Pre-Trip Inspection Test #5 is based on State CDL Manual Section 11.1.2 External Inspection/Trailer
See below for more information or go to our CDL Pre-Trip Inspection Learning Center.
Note: Pre-Trip tests do not have CDL manual reference after each question like our other testing areas. Instead, the whole CDL section that applies to the test can be found at the bottom of each test page for your reference.
Take this same test in our other testing modes …
Official State CDL Manual Section 11.2 External Inspection/Trailer
11.2.1– Steering
Steering Box/Hoses
- Check that the steering box is securely mounted and not leaking. Look for any missing nuts, bolts, and cotter keys.
- Check for power steering fluid leaks or damage to power steering hoses.
Steering Linkage
- See that connecting links, arms, and rods from the steering box to the wheel are not worn or cracked.
- Check that joints and sockets are not worn or loose and that there are no missing nuts, bolts, or cotter keys.
11.2.2 – Suspension
Springs/Air/Torque
- Look for missing, shifted, cracked, or broken leaf springs.
- Look for broken or distorted coil springs.
- If vehicle is equipped with torsion bars, torque arms, or other types of suspension components, check that they are not damaged and are mounted securely.
- Air ride suspension should be checked for damage and leaks.
Mounts
- Look for cracked or broken spring hangers, missing or damaged bushings, and broken, loose, or missing bolts, u-bolts or other axle mounting parts. (The mounts should be checked at each point where they are secured to the vehicle frame and axle/s).
Shock Absorbers
- See that shock absorbers are secure and that there are no leaks.
Note: Be prepared to perform the same suspension components inspection on every axle (power unit and trailer, if equipped).
11.2.3 – Brakes
- Slack Adjustors and Pushrods
- Look for broken, loose, or missing parts.
- For manual slack adjustors, the brake pushrod should not move more than one inch (with the brakes released) when pulled by hand.
Brake Chambers
- See that brake chambers are not leaking, cracked, or dented and are mounted securely.
Brake Hoses/Lines
- Look for cracked, worn, or leaking hoses, lines, and couplings.
Drum Brake
- Check for cracks, dents, or holes. Also check for loose or missing bolts.
- Check for contaminates such debris or oil/grease.
- Brake linings (where visible) should not be worn dangerously thin.
Brake Linings
- On some brake drums, there are openings where the brake linings can be seen from outside the drum. For this type of drum, check that a visible amount of brake lining is showing.
- Note: Be prepared to perform the same brake components inspection on every axle (power unit and trailer, if equipped).
11.2.4 – Wheels
Rims
- Check for damaged or bent rims. Rims cannot have welding repairs.
Tires
- The following items must be inspected on every tire:
- Tread depth: Check for minimum tread depth (4/32 on steering axle tires, 2/32 on all other tires).
- Tire condition: Check that tread is evenly worn and look for cuts or other damage to tread or sidewalls. Also, make sure that valve caps and stems are not missing, broken, or damaged.
- Tire inflation: Check for proper inflation by using a tire gauge. Note: You will not get credit if you simply kick the tires to check for proper inflation.
Hub Oil Seals/Axle Seals
- See that hub oil/grease seals and axle seals are not leaking and, if wheel has a sight glass, oil level is adequate.
Lug Nuts
- Check that all lug nuts are present, free of cracks and distortions, and show no signs of looseness such as rust trails or shiny threads.
- Make sure all bolt holes are not cracked or distorted.
Spacers or Budd Spacing
- If equipped, check that spacers are not bent, damaged, or rusted through.
- Spacers should be evenly centered, with the dual wheels and tires evenly separated.
- Note: Be prepared to perform the same wheel inspection on every axle (power unit and trailer, if equipped).
11.2.5 – Side of Vehicle
Door(s)/Mirror(s)
- Check that door(s) are not damaged and that they open and close properly from the outside.
- Hinges should be secure with seals intact.
- Check that mirror(s) and mirror brackets are not damaged and are mounted securely with no loose fittings.
Fuel Tank
- Check that tank(s) are secure, cap(s) are tight, and that there are no leaks from tank(s) or lines.
Battery/Box
- Wherever located, see that battery(s) are secure, connections are tight, and cell caps are present.
- Battery connections should not show signs of excessive corrosion.
- Battery box and cover or door must be secure.
Drive Shaft
- See that drive shaft is not bent or cracked.
- Couplings should be secure and free of foreign objects.
Exhaust System
- Check system for damage and signs of leaks such as rust or carbon soot.
- System should be connected tightly and mounted securely.
Frame
- Look for cracks, broken welds, holes or other damage to the longitudinal frame members, cross members, box, and floor.
11.2.6 – Rear of Vehicle
Splash Guards
- If equipped, check that splash guards or mud flaps are not damaged and are mounted securely.
Doors/Ties/Lifts
- Check that doors and hinges are not damaged and that they open, close, and latch properly from the outside, if equipped.
- Ties, straps, chains, and binders must also be secure.
- If equipped with a cargo lift, look for leaking, damaged or missing parts and explain how it should be checked for correct operation.
- Lift must be fully retracted and latched securely.
11.2.7 – Tractor/Coupling
Air/Electric Lines
- Listen for air leaks. Check that air hoses and electrical lines are not cut, chafed, spliced, or worn (steel braid should not show through).
- Make sure air and electrical lines are not tangled, pinched, or dragging against tractor parts.
Catwalk
- Check that the catwalk is solid, clear of objects, and securely bolted to tractor frame.
Mounting Bolts
- Look for loose or missing mounting brackets, clamps, bolts, or nuts. Both the fifth wheel and the slide mounting must be solidly attached.
- On other types of coupling systems (i.e., ball hitch, pintle hook, etc.), inspect all coupling components and mounting brackets for missing or broken parts.
Hitch Release Lever
- Check to see that the hitch release lever is in place and is secure.
Locking Jaws
- Look into fifth wheel gap and check that locking jaws are fully closed around the kingpin.
- On other types of coupling systems (i.e., ball hitch, pintle hook, etc.), inspect the locking mechanism for missing or broken parts and make sure it is locked securely. If present, safety cables or chains must be secure and free of kinks and excessive slack.
5th Wheel Skid Plate
- Check for proper lubrication and that 5th wheel skid plate is securely mounted to the platform and that all bolts and pins are secure and not missing.
Platform (Fifth Wheel)
- Check for cracks or breaks in the platform structure which supports the fifth wheel skid plate.
Release Arm (Fifth Wheel)
- If equipped, make sure the release arm is in the engaged position and the safety latch is in place.
Kingpin/Apron/Gap
- Check that the kingpin is not bent.
- Make sure the visible part of the apron is not bent, cracked, or broken.
- Check that the trailer is laying flat on the fifth wheel skid plate (no gap).
Locking Pins (Fifth Wheel)
- If equipped, look for loose or missing pins in the slide mechanism of the sliding fifth wheel. If air powered, check for leaks.
- Make sure locking pins are fully engaged.
- Check that the fifth wheel is positioned properly so that the tractor frame will clear the landing gear during turns.
Sliding Pintle
- Check that the sliding pintle is secured with no loose or missing nuts or bolts and cotter pin is in place.
Tongue or Draw-bar
- Check that the tongue/draw-bar is not bent or twisted and checks for broken welds and stress cracks.
- Check that the tongue/draw-bar is not worn excessively.
Tongue Storage Area
- Check that the storage area is solid and secured to the tongue.
- Check that cargo in the storage area i.e. chains, binders, etc. are secure.
11.4 – Trailer
11.4.1 – Trailer Front
Air/Electrical Connections
- Check that trailer air connectors are sealed and in good condition.
- Make sure glad hands are locked in place, free of damage or air leaks.
- Make sure the trailer electrical plug is firmly seated and locked in place.
Header Board
- If equipped, check the header board to see that it is secure, free of damage, and strong enough to contain cargo.
- If equipped, the canvas or tarp carrier must be mounted and fastened securely.
- On enclosed trailers, check the front area for signs of damage such as cracks, bulges, or holes.
11.4.2 – Side of Trailer
Landing Gear
- Check that the landing gear is fully raised, has no missing parts, crank handle is secure, and the support frame is not damaged.
- If power operated, check for air or hydraulic leaks.
Doors/Ties/Lifts
- If equipped, check that doors are not damaged. Check that doors open, close, and latch properly from the outside.
- Check that ties, straps, chains, and binders are secure.
- If equipped with a cargo lift, look for leaking, damaged or missing parts and explain how it should be checked for correct operation.
- Lift should be fully retracted and latched securely.
Frame
- Look for cracks, broken welds, holes or other damage to the frame, cross members, box, and floor.
Tandem Release Arm/Locking Pins
- If equipped, make sure the locking pins are locked in place and release arm is secured.
11.4.3 – Remainder of Trailer
-
Please refer to Section 11.2 of this manual for detailed inspection procedures regarding the following components:
- Wheels.
- Suspension system.
- Brakes.
- Doors/ties/lift.
- Splash guards.